Most industrial sites have maintenance jobs that are difficult to complete while production is running. Many Australian industrial sites use the Christmas closure to catch up on cleaning, inspections and repairs that are difficult to complete during production. A planned plant shutdown makes that work easier, but the mistake is focusing entirely on maintenance and overlooking what happens to the site and equipment while it’s sitting idle.
Oil and process residues become harder to remove, exposed metal can start to rust, and stagnant water can create problems in drains and sumps. Chemical storage also needs attention, particularly when a site is closing over the warmer months.
A bit of preparation before shutting down can prevent unnecessary work and delays when production resumes.
Here’s what we recommend.
1. Clean and degrease plant and equipment
If machinery is going to be sitting idle, clean it properly before packing it away.
Grease, oil and process residues can become harder to remove the longer they’re left on the equipment. This is particularly noticeable on equipment that is exposed to heat. Leaving contaminants on metal surfaces can also contribute to corrosion and cause irreparable damage.
Where maintenance, storage or inspections are planned, cleaning should be one of the first jobs. It’s much easier to identify leaks, damaged components and worn surfaces when they’re not covered in grease.
Pay particular attention to machinery, conveyors, production equipment, and surrounding floors.
The right degreaser or cleaning product depends on the contamination, the surface material and the cleaning method used.
View Chemron’s degreasing range.
2. Protect exposed metal and moving components
Cleaning equipment removes dirt and contamination, but it can also leave metal surfaces exposed.
For sites operating in coastal or humid environments, corrosion of metal parts is worth considering even during relatively short shutdowns. Temperature changes can cause condensation on equipment, particularly in sheds and buildings without climate control.
Once surfaces have been cleaned and dried, apply a suitable corrosion inhibitor or protective coating where required.
Moving components should also be lubricated according to the equipment manufacturer’s recommendations.
It’s a relatively simple job that can help prevent seized components and surface corrosion when equipment is brought back into service.
View our surface coating range.
3. Inspect electrical equipment and batteries
A shutdown provides an opportunity to inspect and maintain electrical equipment that would otherwise be difficult to access.
Check for contamination, corrosion and moisture around electrical components.
Battery terminals are another area worth inspecting, particularly on forklifts and equipment that may remain unused for an extended period.
Any cleaning or maintenance involving electrical equipment must be carried out by appropriately qualified personnel, following the site’s isolation and safety procedures.
Make sure any cleaning products used are suitable for the equipment and application.
View electrical cleaning products.
4. Clean drains, sumps and waste areas
Drains, sumps, grease traps and wash bays are easy to overlook during shutdown preparations.
Where organic material, oils and other waste have accumulated, leaving these areas unattended can lead to unpleasant odours, blockages and additional cleaning when the site reopens.
Inspect and clean these areas before shutting down, making sure any flushing or treatment is consistent with the site’s wastewater and trade waste requirements.
Waste bins should also be emptied, particularly around lunchrooms and amenities.
There’s little point returning to a clean production area if the drains are blocked and the waste areas haven’t been maintained.
Waste treatment products | Deodorising products
5. Check pest control measures
Many industrial sites can provide plenty of sheltered areas for pests, particularly when buildings are left undisturbed.
Lunchrooms, storerooms, warehouses and outdoor equipment are all worth checking before an extended shutdown. Remove food waste, clean eating areas and inspect potential entry points.
Depending on the site, it may also be worth reviewing existing pest control measures and treating appropriate areas before closing.
During the warmer months, wasps are another consideration. They are particularly prevalent around sheds, roof spaces and equipment enclosures. We covered wasp behaviour and treatment considerations in our guide about wasp control around outdoor areas.
6. Inspect and secure chemical storage areas
Chemical storage should be part of your shutdown plans.
This is particularly important over summer when temperatures inside sheds and shipping containers can become considerably higher than the outside temperature. Heat can degrade some chemical components and can create additional storage risks.
Before shutting down, check the following:
- All chemical containers are properly sealed, labelled and in good condition.
- Incompatible chemicals are appropriately segregated.
- Bunds and secondary containment areas are clear and in good condition.
- Chemicals are stored within their recommended temperature ranges and storage conditions.
- The hazardous chemicals register and relevant Safety Data Sheets are current and accessible.
- Unwanted, expired or deteriorating chemicals have been identified for appropriate disposal.
- Spill response equipment and emergency access remain available.
Any damaged or leaking containers should be dealt with before the site closes.
If your chemical store hasn’t been reviewed recently, a planned shutdown is a good opportunity to address any existing issues.
For more information, read our guide to eliminating chemical storage hazards in manufacturing facilities.
7. Check chemical stock levels before you close
The last thing you want after a shutdown is to discover you’re missing critical chemicals that are needed to get production running.
Before closing, review stock levels for cleaning, maintenance and production chemicals. Look beyond what you’ll need during the shutdown itself. Consider what will be required for the first few weeks after production resumes.
If you’re shutting down over Christmas or another major holiday period, check supplier availability and freight arrangements before leaving orders until the last minute.
Regional and interstate deliveries can take longer during peak periods, and some products may have additional manufacturing or procurement lead times.
Shutdown Checklist
Use this checklist when preparing your site for a planned shutdown.
☐ Clean and degrease plant, machinery and production areas.
☐ Protect exposed metal surfaces against corrosion.
☐ Lubricate moving components where required.
☐ Inspect electrical equipment and battery terminals.
☐ Clean drains, sumps, grease traps and waste areas.
☐ Remove food waste and check pest control measures.
☐ Inspect chemical containers, storage conditions and secondary containment.
☐ Check chemical registers and Safety Data Sheets.
☐ Complete a stocktake of maintenance and production chemicals.
☐ Order the products required for shutdown work and production restart.
Need chemicals or technical advice for your shutdown?
Not every cleaning or maintenance job is best handled with off-the-shelf products. Different contaminants, materials and operating conditions can require different approaches, particularly when dealing with industrial equipment and process residues.
At Chemron, we’re Australian-owned, with manufacturing and technical capabilities based in NSW. We manufacture and supply industrial chemicals for a wide range of applications. Our technical team can help identify suitable products, review your cleaning requirements, and develop custom chemical formulations where standard products aren’t suitable.
If you’re preparing for a shutdown and need advice on chemical selection, cleaning processes or product availability, get in touch with us before the work starts.